Wiki » History » Version 1
Joseph Foley, 2015-09-04 13:33
| 1 | 1 | Joseph Foley | This page is intended for [[RepRaps|one of our RepRap]] implementations - Prusa Mendel. |
|---|---|---|---|
| 2 | |||
| 3 | Check out our [[Diary/Logbook|event-log for Teh Prusa]] |
||
| 4 | |||
| 5 | |||
| 6 | Full partlist: http://reprap.org/wiki/Prusa#Non-Printed_Parts_.28.22vitamins.22.29 |
||
| 7 | |||
| 8 | Visual instructions: http://garyhodgson.com/reprap/prusa-mendel-visual-instructions/ |
||
| 9 | |||
| 10 | |||
| 11 | Flickr assembly walkthrough: https://picasaweb.google.com/bokowski/PrusaMendel# |
||
| 12 | |||
| 13 | |||
| 14 | MK7 stepperstruder was substituted in for the old DC motor struder. -Zarutian |
||
| 15 | |||
| 16 | [[Makerbot_Dori|Makerbot í láni frá Dóra (Makerbot on loan from Dóri)]] |
||
| 17 | |||
| 18 | |||
| 19 | |||
| 20 | Hitaplötu tenging við aðalstjórnborð: |
||
| 21 | http://arduino.cc/en/Hacking/PinMapping2560 |
||
| 22 | http://makerbot.wikidot.com/thingomatic-doc:makerbot-motherboard-2-4 |
||
| 23 | |||
| 24 | Port L pinni 4 getur verið góður candidat fyrir PWM út fyrir hita stýringu |
||
| 25 | |||
| 26 | -Zarutian |
||
| 27 | |||
| 28 | ===Current shopping lists: === |
||
| 29 | Innkaup |
||
| 30 | *Pennar filt /kúlu |
||
| 31 | *Nál / tvinni |
||
| 32 | *límband / ductape |
||
| 33 | *demmel cutter |
||
| 34 | *coathangers |
||
| 35 | *'''plywood 10 mm thick''' for the Platform |
||
| 36 | ====Makerbot store: ==== |
||
| 37 | *2x pack of 8 skate bearings |
||
| 38 | *3x stepper motor driver |
||
| 39 | *1x Mechanical endstop kit |
||
| 40 | *4x Nema17 steppers |
||
| 41 | ====Digikey: ==== |
||
| 42 | *adf |
||
| 43 | ====Pololu==== |
||
| 44 | *1 cheap Nema17 spare |
||
| 45 | *Lots of header connectors and pins |
||
| 46 | *Pin crimper |
||
| 47 | Mc Master |
||
| 48 | *http://www.mcmaster.com/ |
||
| 49 | *Belts and sprockets after Joe examines them |
||
| 50 | |||
| 51 | ===Parts we need=== |
||
| 52 | *Molex 09-50-3041 connectors (a bunch, at least 10) |
||
| 53 | *Molex 08-52-0072 connector crimp pin (a whole bunch, maybe 100) |
||
| 54 | *Cable splitter for stepper control signal |
||
| 55 | *Ribbon cable |
||
| 56 | *Belts (T5 pitch 5 mm wide, at least 3 meters in length) |
||
| 57 | *Timing belt pulleys |
||
| 58 | *Breadboard male pin crimping connectors |
||
| 59 | |||
| 60 | ===Parts we might want=== |
||
| 61 | *Pillow block slider bearings |
||
| 62 | *Normal bushing bearings |
||
| 63 | |||
| 64 | ===Parts Joe will be getting=== |
||
| 65 | *Anti Static Mat(s) |
||
| 66 | *Label Printer |
||
| 67 | *4x Nema 17 Stepper motors ( http://www.sparkfun.com/products/9238 ) |
||
| 68 | *Stacking headers for Arduino shields ( trial one of SAM1202-06-ND - get more from Ada) |
||
| 69 | **Molex C-grid SLs |
||
| 70 | |||
| 71 | ===Parts that we are getting from Makerbot (Gummi)=== |
||
| 72 | *2x 8 pack of 8mm ID, 22mm OD and are 7mm thick. 608 type bearings for $5 each. |
||
| 73 | *3x Stepper Motor Driver v3.3 for $39 each |
||
| 74 | *1x Mechanical Endstop v1.2 (Set of 3) for $30 |